FREE SHIPPINGin most EU countries
for order at least €299
65mm extension tube for ESATTO 3"
PL3600284
When installing ESATTO 3" in a telescope with a long travel focuser (such as those usually found on refractors), it is necessary to take into account the lower travel of ESATTO 3" since it's a micrometric focuser. For this reason we have designed this 65mm extension that can be installed between ESATTO 3" and the telescope tube. A precise dovetail coupling system with 3 screws set at 120° allows you to manually rotate the focuser.
Pay in a single solution or over 3 installments of €46,00*
* Pay in 3 installments is a service offered by Paypal, if available in your state. You can select to pay in 3 installments in Paypal.
Availability:
In Stock
€138.00
Tax included
3
If you pay by bank transfer 134,61 €
Pay in a single solution or over 3 installments of €46,00*
* Pay in 3 installments is a service offered by Paypal, if available in your state. You can select to pay in 3 installments in Paypal.
The Eagle control unit can directly power supply SkyWatcher mounts. We build appropriate 12V power supply cables with various lengths. The Eagle-compatible power cables have on a side the jack (for 12V power supply) of the instrument they are designed for. On the other side they have the plug with screw to prevent being disconnected accidentally from...
Adapter from M81 to M68 with stop ring for ESATTO 3" allows you to connect any camera or accessory with M68 female thread. Just thread this adapter to the M81 thread of the ESATTO 3" draw tube. Thanks to the M68 stop ring for ESATTO 3" you can also fix the camera at a precise angle in order to better frame your camera sensor at the desired object.
When installing ESATTO 3" in a telescope with a long travel focuser (such as those usually found on refractors), it is necessary to take into account the lower travel of ESATTO 3" since it's a micrometric focuser. For this reason we have designed this 40mm extension that can be installed between ESATTO 3" and the telescope tube. A precise dovetail...
This Eagle-compatible power cable allows you to power devices that comes with 5.5 (outer diameter) - 2.5 (inner diameter), positive tip polarity. This cable connects to the 3A port of the EAGLE, with screw connector to avoid unwanted detachment. The cable is 115cm long. By using this cable, you can power devices like the ESATTO focusers and the SESTO...
If you want to use your telescope visually with ESATTO 3" or if you want to connect a camera with a 2" nosepiece, just connect the 2" visual back for ESATTO 3" to the M81 thread of the focuser draw tube. This adapter has an internal brass compression ring to avoid scratching the inserted nosepiece as well as 3 locking screws (120° separation) for a...
Adapter ESATTO 3" for ARCO 3" allows you to connect the rotator to ESATTO 3" microfocuser and control it through the special port on ESATTO. By adding this adapter to ARCO 3", thickness of rotator is 24.5mm.
This Eagle-compatible power cable allows you to power devices that comes with 5.5 (outer diameter) - 2.1 (inner diameter), positive tip polarity. This cable connects to the 8A port of the EAGLE, with screw connector to avoid unwanted detachment. The cable is 115cm long. By using this cable, you can power devices like QHYCCD, ATIK, ZWO, QSI cooled cameras,...
The dovetail clamps provide the connection to telescopes support plates and are useful to create support instruments like side-by-side plates (to support two telescopes in parallel on the same mount) or to allow the precise positioning of the guide rings (to adjust precisely the weight balance).
Our dovetail clamps, unlike the common ones, offer...
If you are searching for the most precise motorized focuser for Borg 90FL and 107FL f3.9, this adapter allows you to connect ESATTO 3" to these telescopes. Remove the original focuser of the Borg 90FL and 107FL f3.9 and install ESATTO 3". In order to reach the focus you can use the same photo adapters that you use with the standard focuser.
If you are searching for the most precise motorized focuser to use the GSO/Orion/TPO Ritchey-Chretien 10, 12, 14 and 16 inches (both aluminum and cabron tubes) for astrophotography, this adapter allows you to connect ESATTO 3" to the M117 thread of these telescope. Optical thickness of the "PL3600236" adapter is 43mm so, when you add the ESATTO 3"...
Adapter ESATTO 3" for Meade 16 inches with 4” thread allows you to connect ESATTO 3" to Meade LX200 SCT, LX200 GPS, LX200-ACF, LX600-ACF, LX800-ACF, LX850-ACF 16 inches telescopes or to all the telescopes that have 4-inch male thread
If you are searching for the most precise motorized focuser for Takahashi TSA120, this adapter allows you to connect ESATTO 3" to this telescope. By adding the optional camera adapters with stop ring you can also connect your Takahashi accessories. Based on the camera and accessories train you want to connect, you may need extenders to reach the focus...
ESATTO robotic focuser is also available in 3" version with 76.3mm free aperture, 25mm of draw tube travel, 8kg of payload capacity and an incredible resolution of 0,04 micron per step! The perfect solution for apochromatic refractors and Ritchey-Chretien or Cassegrain telescopes, and heavy imaging trains with large cameras and accessories like off axis...
When installing ESATTO 3" in a telescope with a long travel focuser (such as those usually found on refractors), it is necessary to take into account the lower travel of ESATTO 3" since it's a micrometric focuser. For this reason we have designed this 40mm extension that can be installed between ESATTO 3" and the telescope tube. A precise dovetail...